Quick answer: Identify the rack and its fitting kit before loosening any bolts. Match the foot, fixings and seal to the maker’s diagram. If only a removable bracket is damaged and the rest of the assembly has been checked and is sound, confirm the replacement part for that exact position. If the roof fixing moves, a bolt spins, or you see roof damage or water ingress, stop and arrange an inspection.
Check the symptom first · See when a replacement makes sense
This checklist is for an FJ Cruiser with an existing roof rack, crossbars or platform. Fitting a complete rack for the first time? Start with the vehicle requirements and the rack maker’s fitting kit for your roof configuration. A replacement bracket is only one component and does not supply that kit.
1. Identify the rack before touching the bolts
Look for a rack brand, model or kit number on the crossbars, legs, tray or purchase paperwork. Take one photo showing the whole rack and another showing where a foot meets the roof. If the rack came with a used FJ and has no identifiable label, send the photos to a roof-rack fitter rather than assuming it is factory equipment.
A fixed mounting point in the roof does not tell you which hardware goes back into it. In the Rhino-Rack RCP25-BK/RCP25R-BK FJ Cruiser fitting guide (PDF), the existing bolts and washers are not used to fit that kit's pads. The guide also specifies sealing washers for that kit. Those instructions apply to the named Rhino-Rack kit only.
Read the fitting sheet against the rack on the vehicle
Find the diagram for the rail, foot or pad, not just the platform’s assembly sheet. Match its attachment method to the vehicle and check the parts list for each fixing. Keep the vehicle documentation and the rack maker’s fitting instructions together; one tells you about the vehicle, the other tells you how that particular equipment attaches.
For each position, note the specified fastener, washer or seal, and whether the instructions distinguish one position from another. Existing screws that start in the same thread still may have the wrong length or shoulder. The parts list is the check to use before reusing what came off the vehicle or buying hardware by appearance.
Photograph the rack before loosening anything. Take one wide shot of the roof and one close-up of the affected foot and its visible fixings. Capture the rack label separately. If there is dampness, photograph where it first appeared and note the last time the rack or its accessories were changed.
2. Inspect the mount, fastener and seal
Start with what you can see without loosening the assembly. A split in a removable bracket and movement in the metal attachment to the roof call for different repairs. A bracket purchase alone does not resolve a damaged roof attachment.
With the vehicle parked and the rack unloaded where you can do so safely, inspect the rack-to-foot joint, the foot-to-roof contact and the visible hardware as distinct areas. Look for shiny rub marks, a gap that differs from the diagram, a damaged seal edge or movement already observed during use. There is no need to reproduce movement by levering on the rack or tightening a suspect bolt.

Swipe sideways to read the full table on a small screen.
| Observation | Next action |
|---|---|
| Rack or foot moves at the roof attachment | Unload the rack safely and have the attachment inspected before using it again. |
| Cracked removable piece; the bolt and roof attachment appear intact | Record the part and position and check them against the rack maker’s diagram. If the attachment is sound and the part is documented, compare the replacement route. |
| Fastener spins, roof metal is deformed, or corrosion affects the attachment | Stop. A fitter needs to check the threads or captive hardware and the surrounding roof. |
| New damp patch or staining near a mount | Leave the rack unloaded if you can unload it safely. Arrange inspection of the sealing system and roof attachment. A new bracket alone will not diagnose or repair a leak. |
A rattle and a leak need different checks
If the noise started after a platform accessory was added, tell the fitter what changed and when the noise occurs. A sound near the roof can come from an accessory, a joint in the rack or a roof fixing. Tightening everything at once can hide which joint is moving or disturb a seal.
If dampness appears after rain, photograph where moisture was first visible inside and note any recent rack work. A damp headlining near a foot is a lead to investigate, not proof of the entry point. Ask the fitter to check the prescribed seal stack and the roof attachment; surface sealant alone does not confirm the source or repair damaged threads.
When a replacement bracket makes sense
For example, if you find a cracked removable bracket at the left rear, match the exact rack, position and part reference before ordering. If that same foot has movement at the roof or the bolt spins, have the attachment assessed first. A visible crack can coexist with another fault.
Part and position known: Compare the 63187-35020 bracket listing only if your rack’s documentation or supplier identifies that reference at the position you need. Check what comes in the exact pack, including any bushes, fixings or seals you may need separately. Matching a vehicle year or seeing a similar part in a photo is only a starting point.
Part or pack still uncertain: Ask us to check the part and pack. Include the details below. If you have movement at the roof, damage or a leak, book a fitter’s inspection first. A parts enquiry cannot verify the condition of the attachment.
Send the details that decide fitment
- Vehicle and rack: build month and year, original market, and whether the rack is Toyota or aftermarket. Include the maker, model or fitting-kit code if visible.
- Exact position: left or right looking forwards, then front, middle or rear as applicable. Include the wide roof photo and a close-up of the affected foot; include a part marking if it is visible without dismantling.
- What you need confirmed: the part reference for that position, how many you need, what the selected pack includes, and whether a separate fitting kit, seal or fastener is needed.
If the reply only confirms the vehicle year, ask it to identify the part and fitting position as well. Confirm the selected pack’s contents before ordering rather than using a count of roof fixings to choose the variant.
3. Have these five things ready before fitting
Once the rack, parts and roof attachment have been checked, work from the current instructions for that system. If the fitting sheet, the specified hardware or a safe way to support the rack is missing, pause at preparation.
- Exact instructions: the rack and fitting kit model, the current fitting sheet, and any vehicle-side requirements.
- Parts: the specified fasteners, washers, seals and other hardware in the rack maker's parts list.
- Support: an unloaded rack and a safe way to support or remove it as the fitting instructions specify.
- Tools: the correct bits and, where the fitting sheet specifies a torque, an appropriate torque tool. Do not use a generic value.
- Completion checks: seating, sealing, fastener checks and any recheck interval listed for your setup.
Compare seating before final tightening
When the rack-specific instructions call for a trial fit, check that each pad or foot seats at its specified contact points and that the seal lies the way the drawing shows. A shaped pad may intentionally leave clearance elsewhere. If you see rocking, an unexplained gap or hardware that bottoms out before clamping, stop and check the parts against the diagram.
Use the current fitting sheet for the tightening sequence, torque and any instructions on thread condition or locking compound. Do not transfer a figure from a different rack, or add compound that the fitting instructions do not specify. If you cannot identify the correct instructions or you suspect damaged threads, hand the job to a fitter.

Stop if the parts do not sit correctly. Do not pull a misaligned mount or compressed seal into place by tightening the bolts. Check the part and its location against the relevant instructions, or have the fitter confirm the interface.
Before the first drive: agree the handover checks
Once the rack is fitted, check the installation with the fitter or against the instructions before carrying anything. Keep the fitting sheet and the rack model in your records so the next person can identify the hardware without taking the assembly apart.
Swipe sideways to read the full table on a small screen.
| Check | What to confirm |
|---|---|
| Seating and fasteners | All required hardware is present and the fastening sequence is complete. Pads and seals are seated as shown in the fitting instructions. |
| Clearance and first use | The installed rack and accessories clear the vehicle as required. Confirm any maker-specified checks or recheck intervals before loading the rack. |
| New noise, movement or water ingress | Stop using a rack that is loose or suspected of damage, and arrange inspection. Note what changed rather than tightening it further. |
Even a sound bracket replacement does not raise the permitted roof load. If you plan to add cargo, check the conditions in both the vehicle and rack documentation. Where they express a total roof load, account for the fitted rack, accessories and cargo together. A driving limit does not establish a parked or occupied-load rating.
Installation FAQ
Can I reuse the fasteners from my current FJ Cruiser rack?
Only where the fitting instructions for that exact rack and kit specify reuse and the hardware is fit for service. Some fitting kits require their own bolts, washers or seals.
What if a roof rack bolt spins but will not come out?
Stop and have the attachment assessed. A spinning fastener may involve the threads or captive hardware; replacing the external bracket alone cannot confirm or repair that problem.
Does replacing the bracket increase roof load capacity?
No increase should be assumed. Check the vehicle and rack-system limits for your exact setup and the relevant conditions of use. This checklist does not specify a load limit.
Can I start fitting without knowing the rack model?
Identify the rack or ask a fitter to identify it first. The fitting method, fasteners and sealing arrangement can differ even when two racks use the same roof area.