Quick answer: Plan roof cargo using the usable platform area, each item’s complete carrier footprint and the permitted attachment positions. Include access and opening space before choosing a layout. Weigh the items with their carriers and restraints, then check the separate roof-load limit. A plan that fits geometrically still needs suitable mounting and restraint.
A recovery board may fit the deck by itself but block a roof-box clamp or leave no room to open a latch. Start with the gear you actually carry, not a lifestyle photograph of a loaded platform.
If your existing platform already supports the documented carriers and passes the checks below, you may not need a replacement. If the problem is a new rattle or movement, have the mounting assessed before changing the packing layout.
This guide provides a measurement-and-layout worksheet. It does not establish a tested recovery-board carrier for the MK platform. Use the Tank 300 roof-load guide for the weight calculation and the awning supplier’s instructions for a separate side-mounted awning.
Measure the complete footprint of each item
Measure the carrier or fixing assembly as well as the object. A board’s outside dimensions do not show its carrier’s base, and a roof box’s shell dimensions do not show the clamp spacing underneath it.
| Item | Measurements or information to record | Space outside the closed footprint |
|---|---|---|
| Recovery boards and carrier | Board and carrier length, width, height and the maker’s attachment arrangement. | Hand access, release pins and the path used to remove the boards. |
| Roof box | External dimensions, approved support spacing and clamp arrangement. | Lid opening, latch access and room to operate the clamps. |
| Bags or chairs | Actual packed dimensions plus the approved container or restraint arrangement. | Access to attachment points and any closure. |
| Platform | Usable deck dimensions and permitted attachment positions. | Clearance to vehicle parts and fitted accessories. |
Use measurements from the actual item or its applicable documentation. For the platform, obtain the installed configuration and attachment information rather than scaling a photograph or using a shipping carton dimension.
Record mass alongside dimensions: weigh the boards with their carrier and pins, the box with its contents and clamps, and bags with their restraints. Keep kilograms separate from millimetres on your worksheet. Check a maker’s mass figure only for the exact supplied configuration.
Make a simple scale plan
- Draw the usable deck outline from its confirmed dimensions.
- Choose a scale, such as 1:10. Divide every real measurement by ten to draw it at that scale.
- Draw or cut out the complete footprints of the carriers and packed items.
- Mark the permitted attachment positions on the same plan.
- Add the opening and hand-access space around each item.
- Try orientations that keep every item supported and allow its maker’s mounting method.

For scale arithmetic only, a 300 mm measurement becomes 30 mm on a 1:10 drawing. That example is not a Tank 300 or MK platform dimension.
A drawing can expose a collision before you order. It cannot approve a carrier, an unsupported overhang or a new attachment point.
Use a pass-and-revise check for each layout
| Check | What a usable plan shows | Revise or stop when |
|---|---|---|
| Support | The item and carrier sit on the support arrangement their instructions permit. | A required support or fixing position is unavailable. |
| Attachment access | Clamps, fasteners and permitted anchors remain reachable. | Another item covers a fixing or prevents fitting with the specified tools. |
| Opening space | Lids, handles and release parts have their required movement space. | You must loosen another item to operate a latch or remove a board. |
| Restraint route | The documented restraint or carrier arrangement can be installed without obstruction. | A strap crosses an edge or a mounting location that its instructions do not permit. |
| Vehicle clearance | The installed setup stays clear of relevant bodywork, glass and equipment. | Vehicle operation or access is restricted contrary to its instructions. |
Keep the permitted mounting positions ahead of convenience. There is no universal rule that dirty boards or light bags belong at the outer edge. Choose positions that meet the equipment instructions, then consider how you will keep dirty items separate from clean bags.
Two common packing conflicts to test
Boards beside a roof box: allow the box lid and latches to operate while the boards remain secured. Check that each board can lift off its pins without hitting the lid, aerial or another carrier. If the two operating spaces overlap, revise the orientation within the permitted mounting positions.
Soft bags beside a board carrier: plan for the bag’s actual packed shape and restraint route. A bag that covers a release pin or forces a strap across the board carrier needs a different position. A separate dirty-board bag may help keep mud away from clean gear, but it does not replace the mounting or restraint system.
Check recovery-board carriers separately
Start with the carrier maker’s fixing method and footprint. Ask the platform supplier whether that arrangement is supported on the selected platform and which hardware is required.
Do not assume a carrier is supplied because recovery boards appear in a product photo. Match the purchased packing list and check fasteners, spacers and any locking or release parts separately.
- Record the board model and the compatible carrier.
- Compare the complete base and fixing positions with the platform’s usable area.
- Keep the removal path and access to retaining parts clear.
- Follow the carrier instructions for securing the boards; this worksheet does not prescribe a restraint pattern.

If you use MAXTRAX equipment, consult the MAXTRAX mounting-pin and flat-rack instructions for the exact board and pin setup. Those instructions address MAXTRAX equipment; they do not establish that an MK platform accepts a particular bracket or that drilling the platform is permitted.
Count mass after the geometric plan
Record the actual packed mass, including each carrier, box, bracket and restraint. A roof box is not automatically a light load; its contents count too. Avoid estimating an item as “light” because it looks bulky.
Use the load guide to compare the actual packed mass with the remaining allowance for your exact vehicle, mounting system and intended conditions. Include the platform, feet and other installed equipment once. A parked rooftop-tent allowance does not establish a driving or off-road cargo limit.
Select a platform rather than a ladder-only option
The MK listing separates the roof platform, ladders, named bundles and a window panel. Only select a bundle when you need and have checked all of its named components. An access ladder is not additional deck area.
Ready to compare your plan? Open MK Frontier Platform Only and request usable-deck and mounting details. Send the item list, carrier instructions and scale plan for an enquiry about the exact configuration.
Check the selected option’s current price on the product page. The listing’s lower ladder-only price must not be treated as the price of the cargo platform.
For an Australian fitment enquiry, provide country, build and model year, exact variant and powertrain, sunroof details, existing roof equipment and attachment photographs. Include the chosen carriers and layout. Confirm the matching mounting kit, hardware contents and delivered cost in AUD before ordering.
Trial access and secure everything before travel
Once the documented equipment is fitted, check the real arrangement from safe access positions. Confirm latches, carrier releases and fixing access before loading for a trip.
Follow the relevant instructions for restraint and inspection. Measure the fully loaded vehicle’s overall height before planning garage access; do not add an unspecified rack height to a brochure figure and treat the result as measured clearance.
If new movement or rattling appears, stop and have the mounting assessed. Repacking around an insecure carrier does not resolve the fixing problem.
Frequently asked questions
Is a recovery-board carrier included with the platform?
Check the exact packing list. Do not infer inclusion from a vehicle or camping photograph. The carrier and its hardware need their own selection and compatibility check.
Can I fill the whole platform if everything fits?
No. You also need the permitted support positions, mounting and restraint arrangements, operating clearances and applicable mass limits.
Should recovery boards always go on the outside edge?
No universal edge position is specified here. Use the permitted carrier and platform attachment arrangement, then plan access and separation from clean gear.
Is a roof box a light item?
Use its actual packed mass together with its mounting equipment. Its contents can materially change the load.
Does a ladder give more mounting positions?
A ladder is separate access equipment, not additional cargo deck or evidence of a carrier-compatible attachment.
Does this plan establish garage clearance?
No. Measure the finished loaded vehicle and compare it with the actual access clearance. This worksheet does not supply a fitted-height figure.
References: current MK platform options and packing-list checks; MAXTRAX mounting instructions; GWM Australia genuine accessory catalogue. The GWM catalogue describes its own equipment and does not approve this aftermarket platform. Confirm any applicable vehicle limit from your vehicle’s own handbook.